Kyros Engineering Engineering Tools
Home › Tools › PCB Trace Designer
// PCB tools Proto v0.1Z0 · Zdiff · CPWGIPC-2221 · IPC-2152Stackup presets

PCB Trace Designer

One place for a trace's impedance, delay, current rating and resistance. Pick a stackup and layer, or type your own dimensions. Then solve the width for 50 Ω or 100 Ω differential, and check that the same trace carries its current without running hot.

Runs entirely in your browser. Nothing is uploaded.

1 · Stackup and layer

2 · Geometry

mm
mm
mm
mm
mm
mm
µm

3 · Target and solve

Ω
Hz

4 · Current and DC

A
°C
°C
mm
×

Example factors from Olson's IPC-2152 walk-through: 1 oz copper 0.84 · a 1 oz plane 0.5 mm below 0.47 · 1.6 mm board 1.08 · FR-4 1.02. Multiply the ones that apply.

Impedance

Z0
—
Solved
—
εeff (static)
—
εeff at f
—
Delay per mm
—
Delay per inch
—
Wavelength at f
—
Z odd
—
Z even
—
Z common
—
One trace alone
—
Coupling k
—
—

Impedance vs trace width

This geometry, swept across width. The dashed line is the target.

Current capacity and DC

Width needed (IPC-2152)
—
Width needed (IPC-2221)
—
This width carries
—
Rise at this current
—
Resistance at 20 °C
—
Resistance hot
—
Voltage drop
—
Power lost
—
—

Temperature rise vs current

At the trace's present width and copper. IPC-2221 is the old chart; IPC-2152 is the newer, measured one.

Width for common currents

At the allowed rise and this copper thickness.

CurrentIPC-2221 externalIPC-2221 internalIPC-2152 (× modifier)
// How it works

Impedance from geometry, width from current

A trace over a plane is a transmission line. Its impedance depends on the ratio of width to dielectric height, the copper thickness, and how much of the field runs in the dielectric versus the air. That share is the effective permittivity εeff. It also sets the speed: delay = √εeff / c, about 5.7–6.0 ps/mm on outer-layer FR-4 and 6.9–7.2 ps/mm inside.

Microstrip: Hammerstad and Jensen

u = w/h Z01(u) = (η0/2π)·ln( f(u)/u + √(1 + (2/u)²) ), f(u) = 6 + (2π − 6)·exp(−(30.666/u)^0.7528) εeff(u) = (εr+1)/2 + (εr−1)/2 · (1 + 10/u)^(−a(u)·b(εr)) thickness: Δu1 = (t/πh)·ln(1 + 4e / ((t/h)·coth²√(6.517u))), Δur = ½(1 + sech√(εr−1))·Δu1 Z0 = Z01(u+Δur) / √εeff(u+Δur) dispersion (Kirschning-Jansen): εeff(f) = εr − (εr − εeff) / (1 + P(f·h))

These fits are better than 0.2 % against exact solutions over most PCB geometries. Against Polar Instruments' boundary-element solver (35 µm copper, 794 µm FR-4, εr 4.2), they land within 0.1 % at 450, 1500 and 3300 µm widths. The one-line IPC-2141 formula, 87/√(εr+1.41)·ln(5.98h/(0.8w+t)), is off by 30 % at the widest of those. The chart shows both curves, so you can see where they diverge.

Stripline, differential pairs and CPWG

stripline (t = 0, exact, Cohn): Z0 = (η0 / 4√εr) · K(k)/K(k'), k = sech(πw/2b) stripline (t > 0, Wheeler 1978): Z0 = (30/√εr)·ln{1 + (4/π)(b−t)/W'·[(8/π)(b−t)/W' + √(((8/π)(b−t)/W')² + 6.27)]} offset stripline: two half-lines, one per plane, capacitances add (εr may differ per side) coupled stripline (Cohn): Z0e,o = (η0 / 4√εr)·K(k'e,o)/K(ke,o), ke = tanh(πw/2b)·tanh(π(w+s)/2b), ko = tanh(πw/2b)/tanh(π(w+s)/2b) coupled microstrip: Kirschning-Jansen 1984 (even/odd εeff and Z), Jansen thickness model Zdiff = 2·Zodd Zcommon = Zeven / 2 coupling k = (Zeven − Zodd)/(Zeven + Zodd) CPWG (Ghione-Naldi): k = a/b, k3 = tanh(πa/2h)/tanh(πb/2h), a = w/2, b = w/2 + s εeff = (Rc + εr·Rb)/(Rc + Rb), Z0 = 60π / (√εeff · (Rc + Rb)), R = K(k)/K(k')

The elliptic integrals are computed exactly with the arithmetic-geometric mean. Solving for width or gap is a bisection on the full model, so the solved value is consistent with every other number on the page.

Current: IPC-2221 and IPC-2152

IPC-2221: I = k · ΔT^0.44 · A^0.725 A in mil², k = 0.048 external, 0.024 internal IPC-2152: A = (117.555·ΔT^−0.913 + 1.15) · I^(0.84·ΔT^−0.108 + 1.159) · modifier width = A / t R = ρ(T)·L/(w·t), ρ(T) = 1.724×10⁻⁸ Ω·m · (1 + 0.00393·(T − 20 °C))

IPC-2221's curve dates from the 1950s and assumed external traces run cooler than internal ones. IPC-2152 replaced it with measured data, which showed the opposite in many builds: FR-4 conducts heat better than still air, so an internal trace near a plane often runs cooler. The fit above follows IPC-2152 Figure 5-2, the baseline chart. That chart is for 3 oz copper in a 1.78 mm polyimide board with no copper planes, in still air. It is conservative for typical boards. A plane under the trace can halve the required area, and the modifier field takes the standard's correction factors.

Limits

References

  1. E. Hammerstad, Ø. Jensen, "Accurate models for microstrip computer-aided design," IEEE MTT-S Int. Microwave Symp. Digest, 1980, pp. 407–409.
  2. M. Kirschning, R. H. Jansen, "Accurate model for effective dielectric constant of microstrip with validity up to millimetre-wave frequencies," Electronics Letters, vol. 18, no. 6, 1982.
  3. M. Kirschning, R. H. Jansen, "Accurate wide-range design equations for the frequency-dependent characteristic of parallel coupled microstrip lines," IEEE Trans. MTT, vol. 32, no. 1, pp. 83–90, 1984. Equations as given in the Qucs technical documentation (coupled microstrip, single microstrip), cross-checked against KiCad's pcb_calculator.
  4. S. B. Cohn, "Characteristic impedance of the shielded-strip transmission line," IRE Trans. MTT, 1954; and "Shielded coupled-strip transmission line," IRE Trans. MTT, 1955.
  5. H. A. Wheeler, "Transmission-line properties of a strip line between parallel planes," IEEE Trans. MTT, vol. 26, 1978.
  6. B. C. Wadell, Transmission Line Design Handbook, Artech House, 1991 (stripline, offset stripline, coupled lines, conductor-backed CPW).
  7. G. Ghione, C. Naldi, "Analytical formulas for coplanar lines in hybrid and monolithic MICs," Electronics Letters, 1984; K. C. Gupta et al., Microstrip Lines and Slotlines, 2nd ed., Artech House, 1996 (CPW thickness correction).
  8. A. J. Burkhardt, C. S. Gregg, J. A. Staniforth, "Calculation of PCB Track Impedance," Polar Instruments, 1999: boundary-element reference values used in this tool's tests.
  9. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, Examples 3.5 and 3.7 (test vectors). M. Steer, Microwave and RF Design, Example 5.6.1 (coupled microstrip test vector).
  10. IPC-2221B, Generic Standard on Printed Board Design; IPC-2152, Standard for Determining Current Carrying Capacity in Printed Board Design, 2009; IPC-2141A, Design Guide for High-Speed Controlled Impedance Circuit Boards.
  11. smps.us, "PCB trace width calculator based on IPC-2152" (curve fit of Figure 5-2). J. Olson, "Determining Circuit Board Current Carrying Capability," PCD&F, 2009 (modifier factors and worked example).
  12. JLCPCB, impedance-controlled stackups (jlcpcb.com/impedance), for the JLC04161H presets.

Laying out a board with fast or high-current nets?

Kyros designs controlled-impedance stackups, high-speed and RF routing, and power paths, then works with the fab to hit the numbers.

Talk about your project →