Kyros Engineering Engineering Tools
Home › Tools › Smith Chart Matcher
// RF tools Proto v0.1Smith chartL-networkStub · λ/4

Smith Chart Matcher

Enter an antenna or load impedance, or click a point on the chart. You get VSWR, return loss and mismatch loss, every L-network that matches it with real E-series parts, and the bandwidth each one actually delivers.

Runs entirely in your browser. Nothing is uploaded.

1 · Load

Ω
Ω
Ω
Hz

2 · Match

dB

Load

VSWR
—
Return loss
—
Mismatch loss
—
Γ (S11)
—
Power reflected
—
Impedance Z
—
Normalized z
—
Equivalent
—
—

Smith chart

Click anywhere on the chart to set the load. The solid line is the selected match, taken from the load to the centre.

Hover for z, Γ and VSWR

L-networks

Every circuit that matches this load to Z0, listed from the load toward the source. Lowpass circuits also attenuate harmonics.

#TypeAt the loadToward sourceLoaded Q

Single shunt stub

Distance from the load to the stub, and the stub length. Lengths use the velocity factor above. Short-circuited stubs are easiest to build.

#Stub atShorted stubOpen stub

Quarter-wave transformer

Slide along the line to a point where the impedance is real, then add a λ/4 section.

#Insert atZ thereSection ZtSection lengthBandwidth
// How it works

Reading the chart, and where the matches come from

The Smith chart is the reflection coefficient plane with the impedance grid drawn on it. A load Z, referred to the system impedance Z0, lands at:

Γ = (Z − Z0) / (Z + Z0) VSWR = (1 + |Γ|) / (1 − |Γ|) return loss = −20·log10|Γ| mismatch loss = −10·log10(1 − |Γ|²)

The centre is a perfect match. Circles are constant resistance, arcs are constant reactance, and the dashed circle through your load is its VSWR circle. Moving toward the generator along a line rotates clockwise around that circle by 2βd.

L-networks

Two reactive elements are enough to match any load with a positive resistance, as long as the circuit type fits the load. In admittance form, Y = G + jB:

shunt element at the load, series toward the source needs G ≤ 1/Z0 B' = ±√(G/Z0 − G²) B_shunt = B' − B X_series = −Im(1 / (G + jB')) series element at the load, shunt toward the source needs R ≤ Z0 X' = ±√(R·(Z0 − R)) X_series = X' − X B_shunt = X' / (R·Z0)

That is up to four circuits. A positive series reactance is an inductor, X = ωL. A negative one is a capacitor, X = −1/(ωC). Shunt susceptance is the mirror: B = ωC or B = −1/(ωL). The loaded Q equals |B'|/G or |X'|/R, and it sets how narrow the match is.

Standard values and bandwidth

Real parts come from E-series values, so the match at f0 is never perfect. The tool rounds each part to the nearest standard value and then sweeps the whole network over frequency. A reactive load is treated as a series inductor (X > 0) or capacitor (X < 0) that scales with frequency, and parts are ideal. The bandwidth is the contiguous range around f0 where return loss stays at or above your spec.

Stub and quarter-wave

stub: t = tan(βd) = [x ± √(r·((1 − r)² + x²))] / (r − 1) z = r + jx = Z/Z0 shorted stub cot(βl) = b open stub tan(βl) = −b (y = 1 + jb at the stub) λ/4: Zt = √(Z0 · Zreal) Zreal = Z0·VSWR at a voltage maximum, Z0/VSWR at a minimum Δf/f0 = 2 − (4/π)·acos( Γm/√(1 − Γm²) · 2√(Z0·Zreal) / |Zreal − Z0| )

Limits

References

  1. D. M. Pozar, Microwave Engineering, 4th ed., Ch. 2.3 (reflection coefficient, VSWR, return loss), §5.1 (lumped-element L-section matching, Example 5.1), §5.2 (single-stub tuning), §5.4 (single-section quarter-wave transformer).
  2. C. Bowick, RF Circuit Design, Ch. 4: L-network matching, Q = √(Rhigh/Rlow − 1).
  3. P. H. Smith, "Transmission Line Calculator", Electronics, Jan 1939.
  4. IEC 60063, preferred number series for resistors and capacitors (E6, E12, E24, E96).

Antenna or RF front end not matching on the bench?

Kyros tunes antennas, matching networks and RF front ends for embedded products, from layout and simulation through VNA measurement and range testing.

Talk about your project →