RF Link Budget
Add up transmit power, antenna gains and losses, subtract the path loss, and compare what arrives with what the receiver needs. You get the link margin, the maximum range, and the fade margin your availability target calls for.
1 · Radio
2 · Antennas and losses
3 · Receiver sensitivity
4 · Path
5 · Reliability
Result
Range
Terrain at this distance
Margin vs distance
Link margin for the chosen model. Zero is the receiver's sensitivity. The dashed line is the fade margin your availability target needs.
Range by model and margin
Same radio and antennas, three path-loss models. Free space is the best case, not a design number.
| Margin held | Free space | Log-distance | Two-ray |
|---|
From transmitter to receiver, in decibels
A link budget is one sum. Everything the signal gains goes in, everything it loses comes out, and what is left is compared with the weakest signal the receiver can decode:
Path-loss models
Free space needs a clear line of sight with the Fresnel zone empty, so it is the best case. Log-distance folds buildings and clutter into one exponent n that you measure or pick from a table. Two-ray models the ground bounce over open flat terrain and falls at 40 dB per decade once the antennas are far enough apart.
Receiver sensitivity
−174 dBm/Hz is kT at 290 K. A datasheet sensitivity implies an SNR for that bandwidth and noise figure, and the tool prints it. If the implied SNR is far from what the modulation needs, check the bandwidth and the datasheet conditions (packet error rate, payload length). LoRa works at negative SNR because spreading gain pulls the signal out of the noise.
Fade margin and availability
A link that works on average fails in deep fades. For a Rayleigh fading channel (no dominant path, the worst case for a mobile or indoor link) the fraction of time the signal stays above a level that is M dB below its median-power level is:
The tool reports the margin your availability target needs and the range you can still reach while holding it. A line-of-sight link with a strong direct path (Rician fading) needs less, so treat the figure as conservative.
Terrain
Keep at least 60 % of r1 clear of obstacles. The optional knife-edge loss uses the ITU-R P.526 approximation with the obstacle (or the earth bulge) treated as a single edge at mid-path.
Limits
- Engineering estimate. Real links also see interference, antenna pattern and polarization mismatch, detuning near the body, and multipath in buildings. Measure before you commit.
- The preset sensitivities are single datasheet or standard-minimum figures at one condition (typically 1 % PER or 30 % PER). Vendors differ. Replace them with your part's table.
- Two-ray assumes a flat, perfectly reflecting ground and isotropic antennas. Add the real gains in section 2.
- The knife-edge option models one obstacle at mid-path. It is not a terrain-profile tool.
- Check your regional limits (FCC Part 15, ETSI EN 300 220 / EN 300 328) for conducted power, EIRP and duty cycle before choosing Tx power and antenna gain.
References
- H. T. Friis, "A Note on a Simple Transmission Formula", Proc. IRE, 1946. Free-space form with the 32.44 constant: Rappaport, Wireless Communications: Principles and Practice, Ch. 4.
- Rappaport, Wireless Communications, Ch. 4: log-distance path loss, ground-reflection (two-ray) model and Rayleigh fading statistics.
- ITU-R P.526, Propagation by diffraction: single knife-edge approximation J(v) = 6.9 + 20·log10(√((v − 0.1)² + 1) + v − 0.1).
- Semtech, SX1276/77/78/79 datasheet, receiver sensitivity table (125 kHz: SF7 −123 dBm to SF12 −137 dBm), and AN1200.22 LoRa Modulation Basics (SNR limits −7.5 dB at SF7 to −20 dB at SF12).
- Nordic Semiconductor, nRF52840 Product Specification, RADIO receiver sensitivity (BLE 1 Mbps −95 dBm, 2 Mbps −92 dBm, coded PHY S=2 −99 dBm, S=8 −103 dBm).
- IEEE 802.15.4 (2.4 GHz PHY minimum receiver sensitivity −85 dBm); Texas Instruments CC2530 datasheet (typical −97 dBm).
- IEEE 802.11-2016, OFDM PHY minimum receiver sensitivity table (20 MHz: 6 Mb/s −82 dBm, 54 Mb/s −65 dBm).
- Texas Instruments, CC1101 datasheet, RF receive section (868 MHz: −112 dBm at 1.2 kBaud, −103 dBm at 38.4 kBaud, about −95 dBm at 250 kBaud).
Link budget closes on paper but not on the bench?
Kyros designs and debugs RF links for embedded products: antenna selection and matching, enclosure detuning, range testing, and the firmware that handles a marginal link gracefully.
