// Electronics tools Proto v0.1Dividers · RC · LCColor code · E-seriesIPC-2221 · RF · op-amps
EE Toolbox
33 everyday electronics calculators on one page: Ohm's law, dividers, RC and LC timing, resistor color codes, trace width, thermal, dB and RF. Type values with SI suffixes like 4.7k, 100n or 2.4G, and the URL holds your numbers so you can share a result.
Runs entirely in your browser. Nothing is uploaded.
// How it works
What is in the toolbox, and what each result means
Each card is one small calculator. Change any input and every result on the page updates. The address bar keeps all your inputs, so copying the URL shares exactly what you see.
- Basics: Ohm's law, power, voltage divider (with a load option), a divider resistor-pair finder, current divider, and series and parallel resistors, capacitors and inductors.
- RC / LC / timing: RC time constant with charge and discharge curves, LC resonance, 555 astable and monostable, and RC filter cutoff.
- Component tools: resistor color code in both directions, E6 to E96 standard value finder, LED resistor, and capacitor energy.
- PCB and thermal: IPC-2221 trace width, microstrip impedance, thermal resistance chain and heatsink sizing.
- Conversion: dBm, watts and volts, AWG and mm², frequency, period and wavelength, temperature, data rate, and voltage and power dB.
- RF and wireless: free-space path loss with a link budget, skin depth, VSWR and return loss, and antenna gain.
- Op-amp quick: non-inverting gain, inverting gain and a transimpedance stage.
Formulas
Ohm V = I·R P = V·I = I²R = V²/R
Divider Vout = Vin · R2‖RL / (R1 + R2‖RL)
Parallel 1/Rp = 1/R1 + 1/R2 + … (capacitors: series and parallel swap)
RC τ = R·C v(t) = V·(1 − e^(−t/τ)) fc = 1/(2π·R·C)
LC f0 = 1/(2π·√(L·C)) Z0 = √(L/C)
555 astable f = 1/(ln2·(R1 + 2·R2)·C) monostable t = ln3·R·C
IPC-2221 I = k · ΔT^0.44 · A^0.725 A in mil², k = 0.048 external, 0.024 internal
FSPL 20·log10(4π·d·f / c)
Skin depth δ = √(2ρ / (2π·f·μ0·μr))
VSWR |Γ| = (VSWR − 1)/(VSWR + 1) RL = −20·log10|Γ| ML = −10·log10(1 − |Γ|²)
Op-amp non-inverting 1 + Rf/Rg inverting −Rf/Rin TIA Vout = −Iin·Rf
Limits
- These are ideal-component and textbook-model estimates. Tolerances, temperature coefficients, parasitics and datasheet limits are not modeled. Verify against your parts.
- IPC-2221 is a DC, steady-state chart fit from the 1950s with 35 A and 10 to 100 °C limits. It is conservative for thin outer traces and does not reflect planes, vias or airflow. IPC-2152 is the modern reference.
- Microstrip covers a single outer-layer trace over a plane. It does not model solder mask, stripline, coupled pairs or frequency dispersion. Confirm controlled-impedance lines with your board house.
- The ampacity shown for wire is a conservative 700 circular mils per amp rule. It is not a code or safety rating.
- FSPL is line-of-sight free space. Real links lose more to terrain, walls, polarization and cables.
- 555 duty cycle with the basic astable network is always above 50 %.
References
- IPC-2221B, Generic Standard on Printed Board Design, section 6.2 (conductor current capacity). IPC-2152, Standard for Determining Current-Carrying Capacity in Printed Board Design.
- IEC 60062, Marking codes for resistors and capacitors (color code), and IEC 60063, Preferred number series for resistors and capacitors (E6 to E192).
- P. Horowitz and W. Hill, The Art of Electronics, 3rd ed., chapters 1 and 4 (dividers, RC networks, op-amp gains).
- Texas Instruments, NE555 Precision Timers datasheet (SLFS022): astable and monostable equations.
- E. Hammerstad and O. Jensen, "Accurate models for microstrip computer-aided design," IEEE MTT-S Symposium Digest, 1980; B. Wadell, Transmission Line Design Handbook, 1991.
- D. Pozar, Microwave Engineering, 4th ed., sections 2.3 to 2.5 (reflection coefficient, SWR, return loss).
- ASTM B258, Standard Specification for Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires.
- H. Johnson and M. Graham, High-Speed Digital Design, 1993 (skin effect in copper).
Need a design checked by an engineer?
Kyros designs and reviews electronics for a living: power, analog front ends, RF, and the boards that have to pass thermal and compliance testing.
